
Inerta 70 Camouflage Paint An11
About the product
Teknos INERTA 70 is a polyurethane camouflage paint. Used as a topcoat in e.g. Camouflage Treatment Systems K110, K110B, K111, K111B, K113 and K113B. The paint contains special reflective properties.
Certificates, approvals and classifications Finnish Defence Forces
Recommended substrate Steel
Binder Polyurethane
Solids 40 ±2% by volume Total solids Approx. 560 g/l
Volatile organic compounds (VOC) Approx. 500 g/l (DIRECTIVE 2010/75/EU) The stated VOC value is the average value for factory-produced products and will therefore depend on differences between the individual products covered by this technical data sheet.
Practical coverage Depends on application technique, surface conditions, overspray, etc.
Gloss (60°) Full matt, semi-matt depending on colour.
Hardener Comp. B: INERTA 70 HARDENER
Mixing ratio (A:B) 8:1 parts by volume
Pot life, 23 °C 6 h
Thinner TEKNOSOLV 9521, TEKNOSOLV 9502.
Storage The storage stability is stated on the label. Store in a cool place in tightly closed packaging.
Pretreatment
PRIMED SURFACES: Degrease and remove dirt. Dry the surface and remove dust and other foreign matter before painting begins. Sand the surfaces if necessary. Other instructions regarding surface pretreatment can be found in the standards EN ISO 12944-4 and ISO 8501-2.
Application method Conventional spraying, Airless spraying.
Application
MIXING OF COMPONENTS: Take the potlife of the mixture into account when calculating the quantity to be mixed at one time. Before application, mix base and hardener in the correct ratio. Stir thoroughly to the bottom of the container. Insufficient stirring or incorrect mixing ratio will result in poor curing and poor film properties.
Stir thoroughly before use. Apply by conventional or airless spray.
Suitable airless nozzle size. 0.011 - 0.015".
Application conditions
The surface to be treated must be dry. During application and drying, the air, surface and product temperature must be above +5 °C and the relative humidity below 80%.
Drying time +23 °C / 50 % RH (dry film 40 µm)
- dust dry 15 min (ISO 9117-3:2010)
- tack-free 1 h (ISO 9117-5:2012)
Inerta 70 camouflage paint is a paintable paint with itself or with TEKNODUR 0210 camouflage clear coat
surface temp +5 °C minimum 1 day.
surface temp +23 °C minimum 6 hours
Cleaning TEKNOCLEAN 6496
Safety and preventive measures See safety data sheet.
Certificates, approvals and classifications Finnish Defence Forces
Recommended substrate Steel
Binder Polyurethane
Solids 40 ±2% by volume Total solids Approx. 560 g/l
Volatile organic compounds (VOC) Approx. 500 g/l (DIRECTIVE 2010/75/EU) The stated VOC value is the average value for factory-produced products and will therefore depend on differences between the individual products covered by this technical data sheet.
Practical coverage Depends on application technique, surface conditions, overspray, etc.
Gloss (60°) Full matt, semi-matt depending on colour.
Hardener Comp. B: INERTA 70 HARDENER
Mixing ratio (A:B) 8:1 parts by volume
Pot life, 23 °C 6 h
Thinner TEKNOSOLV 9521, TEKNOSOLV 9502.
Storage The storage stability is stated on the label. Store in a cool place in tightly closed packaging.
Pretreatment
PRIMED SURFACES: Degrease and remove dirt. Dry the surface and remove dust and other foreign matter before painting begins. Sand the surfaces if necessary. Other instructions regarding surface pretreatment can be found in the standards EN ISO 12944-4 and ISO 8501-2.
Application method Conventional spraying, Airless spraying.
Application
MIXING OF COMPONENTS: Take the potlife of the mixture into account when calculating the quantity to be mixed at one time. Before application, mix base and hardener in the correct ratio. Stir thoroughly to the bottom of the container. Insufficient stirring or incorrect mixing ratio will result in poor curing and poor film properties.
Stir thoroughly before use. Apply by conventional or airless spray.
Suitable airless nozzle size. 0.011 - 0.015".
Application conditions
The surface to be treated must be dry. During application and drying, the air, surface and product temperature must be above +5 °C and the relative humidity below 80%.
Drying time +23 °C / 50 % RH (dry film 40 µm)
- dust dry 15 min (ISO 9117-3:2010)
- tack-free 1 h (ISO 9117-5:2012)
Inerta 70 camouflage paint is a paintable paint with itself or with TEKNODUR 0210 camouflage clear coat
surface temp +5 °C minimum 1 day.
surface temp +23 °C minimum 6 hours
Cleaning TEKNOCLEAN 6496
Safety and preventive measures See safety data sheet.
- Industries: Industrial Metal Finishing
- Brand: Teknos
Inerta 70 Camouflage Paint An11
-
Stock: Delivery 3-4 working days• Order item
-
Item no.: 1770211010
-
Unit: 8 L